We are committed on providing you with the latest and most accurate Motorola Solutions MSC-122 exam preparation products.If you want to pass Motorola Solutions https://www.pass4itsure.com/MSC-122.html exam successfully, do not miss to read latest Flydumps Motorola Solutions MSC-122 on Flydumps.
QUESTION: 1 If a Motorola access point induces a 50 mW RF signal onto a 3 dBi antenna, what will be the resulting EIRP of the transmitted signal?
A. 0 dBm
B. 3 dBm
C. 20 dBm
D. 50 mW
E. 50 dBm
QUESTION: 2 Which of the following statements is NOT considered to be a best practice with respect to the wired backbone serving the WLAN?
A. When performing manual configuration of a point-to-point Ethernet link, ensure that both the speed and the duplex mode settings on the two ports match.
B. When creating a link between Ethernet 10/100BASE-T or 10/100/1000BASE-T ports, enable (or accept the default of) auto-negotiation on both ports.
C. When creating a link between Gigabit Ethernet fiber ports, enable (or accept the default of) auto-negotiation.
D. When creating a link between Gigabit Ethernet fiber ports, disable auto-negotiation on both ports.
QUESTION: 3 You are deploying a new system and are creating the RF Domain(s). Which of the following options would you use to group the APs into the same domain?
A. By VLAN, where all APs are on the same subnet.
B. By site, which can be a location where the group of installed APs can hear each other’s beacons.
C. By name, so they can be easily sorted in the tree view of the controller.
D. By deployment phase, so configurations can be accidentally pushed to newly installed APs.
You are performing a physical site survey of a new WiNG 5 WLAN deployment.
Which of the following is CORRECT?
A. The Signal to Noise Ratio (SNR) is a critical measurement that needs to be addressed.
B. It is acceptable that you use any RF infrastructure device (Access Point) to perform the site survey test.
C. Using default settings of a site survey application will provide an adequate site survey result.
D. Customer throughput requirements are the only criteria for which need to be surveyed.
QUESTION: 5 You have just conducted a throughput test using iPerf on a WLAN that shows a PHY signaling rate of 54 Mbps, however the average throughput rate shown in iPerf is only
23.5 Mbps. What is the most likely explanation for this condition?
A. This throughput speed is considered nominal.
B. This throughput rate could indicate a mismatch between Wi-Fi confidentiality algorithms.
C. This throughput rate indicates excessive user activity.
D. This throughput rate indicates excessive out-of-band interference such as nearby cell phone towers.
QUESTION: 6 During a recent throughput analysis test of your 802.11g network, you discovered that performance is poor in comparison to previous baselines. You discover that this is the result of 802.11b stations becoming associated with your access point. What option could you implement to eliminate 802.lib clients from attaching to your network?
A. Implement protection mechanisms
B. Make 24 mbps a required data rate
C. Implement RTS/CTS at the access point
D. Change the channel used for the network
QUESTION: 7 Your customer has requested that during the upcoming 802.llg to 802.11n upgrade deployment you enable 40 MHz channels on 1, 6, and 11 of the 2.4 GHz ISM band. You respond by saying that there is not enough spectrum to allow 40 MHz channels centered on 1, 6, and 11. How wide are standard 802.11g (OFDM) channels?
A. 20 MHz
B. 83.5 MHz
C. 5 MHz
D. 11 MHz
E. 22 MHz
QUESTION: 8 You have an access point that requires PoE connected to a switch with a 150 meter 10 BASE-T CAT 5 cable. During testing numerous problems with both data transmission and intermittent power occurs. Which of the following is most likely the cause?
A. The cable should be CAT 6
B. There is a duplex mismatch
C. The cable should be 100 BASE-T
D. The cable is too long
Which of the following APs does not support adaptive mode?
Which of the following is the primary method of collision avoidance in an 802.11 CSMA/CA WLAN?
A. Backoff Timer
B. Carrier Sense
C. Contention Window
D. Enhanced Distributed Channel Access (EDCA)
E. Distributed Coordination Function Interframe Spaces (DIFS)
QUESTION: 11 You are designing a WLAN that will support multiple BSS IDs. One of the characteristics you need to take into consideration is that each BSS transmits a beacon every 100 ms. How many BSSs can be enabled on the following Motorola access points under WiNG 5: AP7131, AP650, AP6532?
A. 2, one per radio
B. 1 per AP, it is shared between the radios to provide seamless roaming
C. 8, four per radio
D. 16, eight per radio
QUESTION: 12 You are deploying a new WLAN within the WiNG 5 architecture. Which of the following is the only UNSUPPORTED Motorola access point/port?
QUESTION: 13 Your customer has requested that you configure unique VLANs for voice, normal user data with 802.1X security, guest access, and management traffic. Which of the following VLAN modes can support this request?
A. Native Mode
B. Access Mode
C. Trunk Mode
D. Aggregation Mode
E. Encapsulation Mode
QUESTION: 14 Which of the following statements regarding the configuration of Motorola RFS controllers is TRUE?
A. ADSP can be used to push CLI profiles to APs and controllers.
B. LANPlanner can be used to push CLI profiles to APs and controllers.
C. RFMS can be used to perform predictive site surveys using an RFS controller
D. WiNG 5 can be used to perform manual site surveys using an RFs controller
E. CLI can be used to perform both manual and predictive site surveys using an RFS controller.
QUESTION: 15 You have configured a Motorola RFS controller using WiNG 5 and have attempted to adopt a group of APs using L2 adoption but the adoption is not successful. You have confirmed the following:
-All of the APs have an Ethernet connection to the same LAN segment as the controller
-Spanning Tree Protocol (STP) has been disabled on the APs next hop switch port
Intermediate firewalls are not blocking EtherType 0x8783 Given this scenario, which of the following is the most likely cause of the unsuccessful AP adoption?
DHCP option 192 has not been defined on the DHCP server
A local VLAN has been configured on both the controller and the APs
The APs GE ports have been configured for an S02.1q-tagged native VLAN
The APs GE ports have been configured for an 802.1q-untagged native VLAN
Which of the following are methods that may be used to perform the initial configuration of an RFS controller using WiNG 5 (select THREE)?
A. Static configuration using SNMP
B. Automated self-configuration using Smart RF
C. Manual configuration using GUI
D. Manual configuration using CLI
E. Manual configuration using RFS Activator application
F. Automated configuration using wizard
Answer: C, D, F
QUESTION: 17 You are deploying a new WiNG 5 WLAN system and the client will have several different types of access points, Independent AP licenses within WiNG 5 controllers apply to all of the following access points, EXCEPT:
QUESTION: 18 Extended VLANs are configured by marking a VLAN on an AP or RFS controller as extended. Which of the following are methods by which extended VLAN configurations may be pushed to access points (select TWO)?
A. DHCP options
B. RF domain profile
C. Policy refresh
D. Device profiles
E. Manual overrides
F. RF Domain updates
Answer: D, E
Which of the following interfaces are recommended to be used for local management of an RFS6000 or RFS7000?
A. Gigabyte Ethernet (GE)
B. Management Ethernet (ME)
C. Uplink (UP)
D. Universal Serial Bus (USB)
QUESTION: 20 You have configured a Motorola RFS controller with multiple VLANs. You have configured the native VLAN as VLAN 6, management traffic to use VLAN 8, voice traffic to flow over VLAN 18, and guest Internet access as VLAN 21. On which VLAN will untagged frames be placed after they arrive at the controller?
A. VLAN 1
B. VLAN 6
C. VLAN 8
D. VLAN 18
E. VLAN 21
QUESTION: 21 During the deployment of a WLAN, the use of specialized helper applications is indispensible. These hardware components and computer programs allow the deployment engineer to visualize the invisible energy patterns that compose the RF channels. Which of the following best describes a specialized application that allows the deployment engineer to gather OSI Model Layer 1 and Layer 2 activity, in real time, and model the combined effects, superimposed on a representative background image?
A. Protocol Analyzer
B. Spectrum Analyzer
C. WLAN Discovery tool
D. Manual Site Survey tool
E. Predictive Site Survey tool
QUESTION: 22 Which of the following interfaces found on an RFS4000 or RFS6000 Controller can be used to supply Power over Ethernet to directly attached APs?
A. Gigabyte Ethernet (GE)
B. Uplink (UP)
C. Management Ethernet (ME)
D. Universal Serial Bus (USB)
Flydumps is an excellent source of information on IT Certifications. In the Flydumps, you can find study skills and learning materials for your exam. Flydumps Motorola Solutions MSC-122 dumps are studied by the experienced IT experts. It has a strong accuracy and logic. To encounter Flydumps, you will encounter the best Motorola Solutions https://www.pass4itsure.com/MSC-122.html dumps. You can rest assured that using our Motorola Solutions MSC-122 dumps. With it, you have done fully prepared to meet this Motorola Solutions MSC-122 exam.